Analysis of a Flexible Photoconductor, Manufactured with Organic Semiconductor Films.

This work presents the evaluation of the electrical behavior of a flexible photoconductor with a planar heterojunction architecture made up of organic semiconductor films deposited by high vacuum evaporation. The heterojunction was characterized in its morphology and mechanical properties by scanning electron microscopy and atomic force microscopy. The electrical characterization was carried out through the approximations of ohmic and SCLC (Space-Charge Limited Current) behaviors using experimental J-V (current density-voltage) curves at different voltages and under different light conditions. The optimization of the photoconductor was carried out through annealing and accelerated lighting processes. With these treatments, the Knoop Hardness of the flexible photoconductor has reached a value of 8 with a tensile strength of 5.7 MPa. The ohmic and SCLC approximations demonstrate that the unannealed device has an ohmic behavior, whereas the annealed device has an SCLC behavior, and after the optimization process, an ohmic behavior and a maximum current density of 0.34 mA/mm2 were obtained under blue light. The approximations of the device's electron mobility (µn) and free carrier density (n0) were performed under different light conditions, and the electrical activation energy and electrical gap were obtained for the flexible organic device, resulting in appropriate properties for these applications.

Stent-assisted Woven EndoBridge embolization for the treatment of pulsatile tinnitus caused by an ipsilateral high-riding jugular bulb.

PURPOSE: Pulsatile tinnitus can be caused by a high-riding jugular bulb (HRJB), characterized by the superior position of the jugular bulb in the petrous temporal bone. The anatomical position and morphology of this entity make it challenging for endovascular treatment. We report our experience with two patients successfully treated with a stent-assisted Woven EndoBridge (WEB; Microvention, Tustin, CA, USA) device. MATERIALS AND METHODS: We describe two cases of HRJB in patients presenting with disabling pulsatile tinnitus. Temporary balloon occlusion of the jugular bulb prior to the intervention reduced tinnitus intensity. Both patients were subsequently treated under general anesthesia with the WEB device deployed in the HRJB which was held by a stent deployed in the sigmoid sinus. RESULTS: Both procedures were successful with good positioning of the WEB device and no procedural complications. Both patients had complete resolution of pulsatile tinnitus immediately after the procedure. Follow-up imaging showed successful occlusion of the venous cavity with a widely patent stent. CONCLUSION: Among patients with pulsatile tinnitus caused by an ipsilateral HRJB, a stent-assisted WEB device seems to be a viable endovascular option with angiographic and clinical success.

Structural determination, characterization and computational studies of doped semiconductors base silicon phthalocyanine dihydroxide and dienynoic acids.

The chemical doping of silicon phthalocyanine dihydroxide (SiPc(OH)2), with (2E, 4Z)-5, 7-diphenylhepta-2, 4-dien-6-ynoic acids (DAc) with electron-withdrawing (BrDAc) and electron-donating (MeODAc) substituents is the main purpose of this work. Theoretical calculations were carried out on Gaussian16 software, with geometrical optimization of all involved species, and obtention of the highest occupied molecule orbital (HOMO), lowest unoccupied molecular orbital (LUMO), and the respective energy gaps. The theoretical calculations show two hydrogen bridge formations: the first one as a peripheral interaction between the terminal oxygen atoms from the acid unit and hydrogen atoms from the phthalocyanine aromatic rings. The second one as the interaction at the nitrogen atoms of the phthalocyanine, which are compelled to form a new flat plane far from the original flat phthalocyanine deck. These organic semiconductors were deposited as thin films and characterized by IR spectroscopy, atomic force microscopy (AFM), and the optical parameters were gathered from UV-Vis studies. The indirect and direct optical band gap, the onset gap and the Urbach energy were obtained. In order to compare the effect of the acids as dopants of the silicon phthalocyanine, the SiPc(OH)2-DAc films were electrically characterized. The SiPc(OH)2-DAc films exhibit an ambipolar electrical behavior, which is influenced by the incidence of different lighting conditions at voltages above 0.3V. The glass/ITO/SiPc(OH)2-MeODAc/Ag reaches a maximum current of 5.68 × 10-5 A for natural light condition, while the glass/ITO/SiPc(OH)2-BrDAc/Ag, reaches a maximum current of 9.21 × 10-9 A for white illumination condition.

Using Recycled Tetrapak and Doped Titanyl/Vanadyl Phthalocyanine to Make Solid-State Devices.

In this work we studied the semiconductor behavior of titanyl phthalocyanine (TiOPc) and vanadyl phthalocyanine (VOPc), doped with anthraflavic acid and deposited on Tetrapak/graphite as flexible electrodes. The molecular structure was approached using the density functional theory and astonishingly, it was found that the structure and electronic behavior can change depending on the metal in the phthalocyanine. Experimentally, the Root Mean Square was found to be 124 and 151 nm for the VOPc-Anthraflavine and TiOPc-Anthraflavine films, respectively, and the maximum stress was 8.58 MPa for the film with VOPc. The TiOPc-Anthraflavine film presents the smallest fundamental gap of 1.81 eV and 1.98 eV for indirect and direct transitions, respectively. Finally, the solid-state devices were fabricated, and the electrical properties were examined. The tests showed that the current-voltage curves of the devices on Tetrapak and VOPc-Anthraflavine on a rigid substrate exhibit the same current saturation behavior at 10 mA, which is achieved for different voltage values. Since the current-voltage curves of the TiOPc-Anthraflavine on a rigid substrate presents a defined diode model behavior, it was approximated by nonlinear least squares, and it has been determined that the threshold voltage of the sample for the different lighting conditions is between 0.6 and 0.8 volts.

Design of Promising Uranyl(VI) Complexes Thin Films with Potential Applications in Molecular Electronics.

In this work, it is proposed the development of organic semiconductors (OS) based on uranyl(VI) complexes. The above by means of the synthesis and the characterization of the complexes by Infrared spectroscopy, Nuclear magnetic resonance spectroscopy, mass spectrometry, and X-ray diffraction. Films of these complexes were deposited and subsequently, topographic and structural characterization was carried out by Scanning Electron Microscopy, X-ray diffraction, and Atomic Force Microscopy. Additionally, the nanomechanical evaluation was performed to know the stiffness of uranyl films using their modulus of elasticity. Also, the optical characterization took place in the devices and their bandgap value ranges between 2.40 and 2.93 eV being the minor for the film of the uranyl complex with the N on pyridine in position 4 (2 c). Finally, the electrical behavior of the uranyl(VI) films was evaluated, and important differences were obtained: the uranyl complex with the N on pyridine in position 2 (2 a) film is not influenced by changes in lighting and its current density is in the order of 10-3  A/cm2 . The film with uranyl complex with the N on pyridine in position 3 (2 b) and 2 c presents a greater current flow under lighting conditions and two orders of magnitude larger than in film 2 a. In these films 2 b and 2 c, ohmic behavior occurs at low voltages, while at high voltages the charge transport changes to space-charge limited current behavior.

Preparation of Hybrid Films Based in Aluminum 8-Hydroxyquinoline as Organic Semiconductor for Photoconductor Applications.

In the present work, we have investigated an organic semiconductor based on tris(8-hydroxyquinoline) aluminum (AlQ3) doped with tetracyanoquinodimethane (TCNQ), which can be used as an organic photoconductor. DFT calculations were carried out to optimize the structure of semiconductor species and to obtain related constants in order to compare experimental and theoretical results. Subsequently, AlQ3-TCNQ films with polypyrrole (Ppy) matrix were fabricated, and they were morphologically and mechanically characterized by Scanning Electron Microscopy, X-ray diffraction and Atomic Force Microscopy techniques. The maximum stress for the film is 8.66 MPa, and the Knoop hardness is 0.0311. The optical behavior of the film was also analyzed, and the optical properties were found to exhibit two indirect transitions at 2.58 and 3.06 eV. Additionally, photoluminescence measurements were carried out and the film showed an intense visible emission in the visible region. Finally, a photoconductor was fabricated and electrically characterized. Applying a cubic spline approximation to fit cubic polynomials to the J-V curves, the ohmic to SCLC transition voltage VON and the trap-filled-limit voltage VTFL for the device were obtained. Then, the free carrier density and trap density for the device were approximated to n0=4.4586×10191m3 and Nt=3.1333×10311m3, respectively.

Lineage-specific mutation of Lmx1b provides new insights into distinct regulation of suture development in different areas of the calvaria.

The calvaria (top part of the skull) is made of pieces of bone as well as multiple soft tissue joints called sutures. The latter is crucial to the growth and morphogenesis of the skull, and thus a loss of calvarial sutures can lead to severe congenital defects in humans. During embryogenesis, the calvaria develops from the cranial mesenchyme covering the brain, which contains cells originating from the neural crest and the mesoderm. While the mechanism that patterns the cranial mesenchyme into bone and sutures is not well understood, function of Lmx1b, a gene encoding a LIM-domain homeodomain transcription factor, plays a key role in this process. In the current study, we investigated a difference in the function of Lmx1b in different parts of the calvaria using neural crest-specific and mesoderm-specific Lmx1b mutants. We found that Lmx1b was obligatory for development of the interfrontal suture and the anterior fontanel along the dorsal midline of the skull, but not for the posterior fontanel over the midbrain. Also, Lmx1b mutation in the neural crest-derived mesenchyme, but not the mesoderm-derived mesenchyme, had a non-cell autonomous effect on coronal suture development. Furthermore, overexpression of Lmx1b in the neural crest lineage had different effects on the position of the coronal suture on the apical part and the basal part. Other unexpected phenotypes of Lmx1b mutants led to an additional finding that the coronal suture and the sagittal suture are of dual embryonic origin. Together, our data reveal a remarkable level of regional specificity in regulation of calvarial development.

Influence of the Polymeric Matrix on the Optical and Electrical Properties of Copper Porphine-Based Semiconductor Hybrid Films.

In this study, we assessed the electrical and optical behavior of semiconductor hybrid films fabricated from octaethyl-21H,23H-porphine copper (CuP), embedded in polymethylmethacrylate (PMMA), and polystyrene (PS). The hybrid films were characterized structurally and morphologically using infrared spectroscopy (IR), atomic force microscopy (AFM), scanning electron microscopy (SEM), and X-ray diffraction (XRD). Subsequently, the PMMA:CuP and PS:CuP hybrid films were evaluated optically by UV-vis spectroscopy, as well as electrically, with the four-point collinear method. Hybrid films present a homogeneous and low roughness morphology. In addition, the PS matrix allows the crystallization of the porphin, while PMMA promotes the amorphous structure in CuP. The polymeric matrix also affects the optical behavior of the films, since the smallest optical gap (2.16 eV) and onset gap (1.89 eV), and the highest transparency are obtained in the film with a PMMA matrix. Finally, the electrical behavior in hybrid films is also affected by the matrix: the largest amount of current carried is approximately 0.01 A for the PS:CuP film, and 0.0015 A for the PMMA:CuP film. Thanks to the above properties, hybrid films are promising candidates for use in optoelectronic devices.

Employing Indirect Adenosine 2A Receptors (A2AR) to Enhance Osseointegration of Titanium Devices: A Pre-Clinical Study.

The present study aimed to evaluate the effect of dipyridamole, an indirect adenosine 2A receptors (A2AR), on the osseointegration of titanium implants in a large, translational pre-clinical model. Sixty tapered, acid-etched titanium implants, treated with four different coatings ((i) Type I Bovine Collagen (control), (ii) 10 µM dipyridamole (DIPY), (iii) 100 µM DIPY, and (iv) 1000 µM DIPY), were inserted in the vertebral bodies of 15 female sheep (weight ~65 kg). Qualitative and quantitative analysis were performed after 3, 6, and 12 weeks in vivo to assess histological features, and percentages of bone-to-implant contact (%BIC) and bone area fraction occupancy (%BAFO). Data was analyzed using a general linear mixed model analysis with time in vivo and coating as fixed factors. Histomorphometric analysis after 3 weeks in vivo revealed higher BIC for DIPY coated implant groups (10 µM (30.42% ± 10.62), 100 µM (36.41% ± 10.62), and 1000 µM (32.46% ± 10.62)) in comparison to the control group (17.99% ± 5.82). Further, significantly higher BAFO was observed for implants augmented with 1000 µM of DIPY (43.84% ± 9.97) compared to the control group (31.89% ± 5.46). At 6 and 12 weeks, no significant differences were observed among groups. Histological analysis evidenced similar osseointegration features and an intramembranous-type healing pattern for all groups. Qualitative observation corroborated the increased presence of woven bone formation in intimate contact with the surface of the implant and within the threads at 3 weeks with increased concentrations of DIPY. Coating the implant surface with dipyridamole yielded a favorable effect with regard to BIC and BAFO at 3 weeks in vivo. These findings suggest a positive effect of DIPY on the early stages of osseointegration.

Fabrication and Characterization of Hybrid Films Based on NiFe2O4 Nanoparticles in a Polymeric Matrix for Applications in Organic Electronics.

Hybrid films for applications in organic electronics from NiFe2O4 nanoparticles (NPs) in poly(3,4 ethylene dioxythiophene), poly(4-styrenesulfonate) (PEDOT:PSS), and poly(methyl methacrylate) (PMMA) were fabricated by the spin-coating technique. The films were characterized by infrared spectroscopy, atomic force microscopy, scanning electron microscopy, and energy-dispersive spectroscopy to subsequently determine their optical parameters. The electronic transport of the hybrid films was determined in bulk heterojunction devices. The presence of NiFe2O4 NPs reinforces mechanical properties and increases transmittance in the hybrid films; the PEDOT:PSS-NiFe2O4 NPs film is the one that has a maximum stress of 28 MPa and a Knoop hardness of 0.103, while the PMMA-NiFe2O4 NPs film has the highest transmittance of (87%). The Tauc band gap is in the range of 3.78-3.9 eV, and the Urbach energy is in the range of 0.24-0.33 eV. Regarding electrical behavior, the main effect is exerted by the matrix, although the current carried is of the same order of magnitude for the two devices: glass/ITO/polymer-NiFe2O4 NPs/Ag. NiFe2O4 NPs enhance the mechanical, optical, and electrical behavior of the hybrid films and can be used as semi-transparent anodes and as active layers.

Evolution of the Viscoelastic Properties of Filler Reinforced Rubber under Physical Aging at Room Temperature.

Filler reinforced rubber is widely used for engineering applications; therefore, a sound characterization of the effects of physical aging is crucial for accurately predicting its viscoelastic properties within its operational temperature range. Here, the torsion pendulum is used to monitor the evolution of the storage and loss modulus of carbon black filled samples for four days after a temperature drop to 30 °C. The storage modulus presents a continuous increase, while the loss modulus generally displays a steady decrease throughout the four days that each test was conducted. The relationship of the recovery rates with the carbon black properties is also studied, analysing its dependency on the particle size and aggregate structure. The evolution of the recovery rate seems to depend linearly on the surface area while the carbon black structure appears to have a much weaker influence on the physical aging behavior for the set of compounds tested. The obtained results corroborate the presence of physical aging at room temperature for filler rubber materials and the ability of the torsion pendulum to monitor the storage and loss modulus change, providing pivotal data on the influence of physical aging on the viscoelastic properties of the material.

The vasculature of neurogenic niches: Properties and function.

In the adult rodent brain, neural stem cells (NSCs) reside in the subventricular zone (SVZ) of the lateral ventricles and the subgranular zone (SGZ) of the hippocampus. In these areas, NSCs and their progeny integrate intrinsic signals and extrinsic cues provided by their microenvironment that control their behavior. The vasculature in the SVZ and SGZ, and the choroid plexus (ChP) in the SVZ, have emerged as critical compartments of the neurogenic niches as they provide a rich repertoire of cues to regulate NSC quiescence, proliferation, self-renewal and differentiation. Physical contact between NSCs and blood vessels is also a feature within the niches and supports different processes such as quiescence, migration and vesicle transport. In this review, we provide a description of the brain and choroid plexus vasculature in both stem cell niches, highlighting the main properties and role of the vasculature in each niche. We also summarize the current understanding of how blood vessel- and ChP-derived signals influence the behavior of NSCs in physiological adulthood, as well as upon aging.

Real-world data evaluation of PAP responsiveness in pediatric obstructive sleep apnea.

STUDY OBJECTIVES: The use of positive airway pressure (PAP) in children is a complex process determined by multiple factors. There are limited data on the response of the pediatric population to PAP therapy at home. The goal of the study was to examine real-world responses using PAP home monitoring in children with obstructive sleep apnea. METHODS: The study included PAP therapy data for 195 children aged between 1 month and 18 years with obstructive sleep apnea and polysomnogram baseline study. We collected demographics, clinical variables, and polysomnogram parameters in all study participants. The individual response to PAP therapy was calculated comparing the apnea-hypopnea index (AHI) in the initial polysomnogram with the mean AHI provided by the download of PAP devices. Multivariate models (logistic regression) were used to examine the predictors of positive PAP response defined as a reduction in AHI ≥ 75%. RESULTS: We found excellent responses to PAP therapy in children (median 85% AHI reduction). However, there was substantial heterogeneity in AHI reductions while on PAP therapy. The best PAP responses were linked to more severe obstructive sleep apnea and higher PAP levels. We also identified that the response to PAP was higher in obese children and lower in males. The best predictive model for individual PAP response was biological sex, obesity, and obstructive AHI ≥ 20 events/h (area under the receiver operating characteristic curve of 0.791). CONCLUSIONS: Real-world data show that PAP is overall an effective therapy in children but the response is heterogeneous. Obstructive sleep apnea parameters and individual factors can be used to predict individual AHI reductions while on PAP and optimize PAP responses at home. CITATION: Aguilar H, Kahanowitch R, Weiss M, et al. Real-world data evaluation of PAP responsiveness in pediatric obstructive sleep apnea. J Clin Sleep Med. 2023;19(7):1313-1319.

Developmental changes in obstructive sleep apnea and sleep architecture in Down syndrome.

BACKGROUND: Down syndrome (DS, also known as Trisomy 21) is a condition associated with abnormal neurodevelopment and a higher risk for sleep apnea. Our study sought to better understand and characterize the age-related developmental differences in sleep architecture and obstructive sleep apnea (OSA) severity in children with DS compared to euploid individuals. METHODS: Retrospective review of polysomnograms in over 4151 infants, children, and adolescents in the pediatric sleep center at Children's National Hospital in Washington D.C. (0-18 years) including 218 individuals with DS. RESULTS: The primary findings of our study are that: (1) severe OSA (obstructive apnea-hypopnea index ≥ 10/h) was more prevalent in the DS group (euploid 18% vs. DS 34%, p < 0.001) with the highest OSA severity being present in young children (<3 years old) and adolescents (>10 years old), (2) abnormalities in sleep architecture in children with DS were characterized by a prolonged rapid-eye movement (REM) sleep onset latency (SOL) (euploid 119 min vs. DS 144 min, p < 0.001) and greater arousal indexes (euploid 10.7/h vs. DS 12.2/h, p < 0.001), (3) developmental changes in the amount of REM sleep or slow wave sleep were not different in DS individuals relative to euploid children, (4) multivariate analyses showed that OSA and REM sleep latency differences between DS and euploid individuals were still present after adjusting by age, biological sex, and body mass index. CONCLUSION: Severe OSA is highly prevalent in children with DS and follows an age-dependent "U" distribution with peaks in newborns/infants and children >10 years of age. Children with DS also have disturbances in sleep architecture characterized by a longer REM SOL and elevated arousal indexes. As sleep cycle generation and continuity play crucial roles in neuroplasticity and cognitive development, these findings offer clinically relevant insights to guide anticipatory guidance for infants, children, and adolescents with DS.

Pentacoordinated Organotin(IV) Complexes as an Alternative in the Design of Highly Efficient Optoelectronic and Photovoltaic Devices: Synthesis and Photophysical Characterization.

The synthesis of four pentacoordinated organotin(IV) complexes prepared in a one-pot reaction from 2-hydroxy-1-naphthaldehyde, 2-amino-3-hydroxypyridine and organotin oxides is reported. The complexes were characterized by UV-Vis, IR, MS, 1H, 13C and 119Sn NMR techniques. The compound based on 2,2-diphenyl-6-aza-1,3-dioxa-2-stannanaphtho[1,2-h]pyrido[3,2-d]cyclononene revealed the formation of a monomeric complex with a distorted five-coordinated molecular geometry intermediate between the trigonal bipyramidal and square pyramidal. In order to find possible applications in photovoltaic devices, hybrid films of organotin(IV) complexes embedded in poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) with graphene were deposited. The topographic and mechanical properties were examined. The film with the complex integrated into the cyclohexyl substituent has high plastic deformation, with a maximum stress of 1.69 × 107 Pa and a Knoop hardness of 0.061. The lowest values of 1.85 eV for the onset gap and 3.53 eV for the energy gap were obtained for the heterostructure having the complex with the phenyl substituent. Bulk heterojunction devices were fabricated; these devices showed ohmic behavior at low voltages and a space-charge-limited current (SCLC) conduction mechanism at higher voltages. A value of 0.02 A was found for the maximum carried current. The SCLC mechanism suggests hole mobility values of between 2.62 × 10-2 and 3.63 cm2/V.s and concentrations of thermally excited holes between 2.96 × 1018 and 4.38 × 1018 m-3.